There are a wide variety of pants and skirts, including casual pants, leggings, jeans, wide leg pants, leggings, suit pants, strap pants, casual water pants, etc; In terms of skirts, there are various types such as silk skirts, cotton and linen skirts, lace skirts, printed skirts, half length skirts, denim skirts, tank top skirts, etc. There are countless types. The inspection methods for pants and skirts can be summarized as follows: the appearance is clean and tidy, and the three-dimensional sense is obvious. In most inspections, the finished product needs to be placed on a cutting board to check the appearance quality. The inspection standards for the appearance quality of pants and skirts: (1) High quality suits, pants or skirts are mostly made of wool and blended fabrics, with an overall sensory effect emphasizing flatness and regularity. For women's clothing, attention is paid to the softness and smoothness of the waist. The main inspection contents include: whether there is obvious color difference on the body, usually the color difference level of the lower crotch seam and waist should be lower than that of other surfaces, There should be no significant color difference between pieces (this issue should be resolved before cutting). (2) The hair direction of the inverted hair and yin and yang grid fabrics should be consistent, and the hair direction of the long hair fabric should be downward. Special patterns should be consistent throughout the body according to the main picture. (3) Alignment: Cover, teeth, side cushion pocket, back middle seam, front middle seam, outer seam, inner long seam. (4) Symmetrical parts: The maximum tolerance for the size and length of the hem of the pants should not exceed 0.5CM. The height requirement for the size of the pants pocket should not exceed 0.5CM. The length and distance of the provincial road must be the same, and the limit tolerance cannot exceed 0.3CM. (5) Observe if there are any defects in the fabric of the garment body. At most one defect is allowed in each part (no defects are allowed above the front hip circumference). (6) Each part of the garment should be ironed flat and should not have a suede surface, yellow surface, aurora, water stains, discoloration, etc. The adhesive lining used should not have glue leakage or bubbles. The buttocks should be smooth, and the pants should be straight. (7) Each part of the circuit should be straight without jumpers, with neat and firm broken wires, flat and beautiful. The tension between the surface and bottom wires should be appropriate. The needle should be knocked down when starting and closing, and there should be no traces caused by the needle plate or lower steel teeth. (8) Finished appearance: The waistline, lining, and lining are smooth and elastic, suitable for consistent width and straightness. The placket surface, lining, and lining are smooth and elastic, with a suitable length tolerance of 0.3CM. The front placket cannot be shorter than the inner placket, and the small crotch seal of the front placket must be smooth and secure, with clear and smooth stitching. The specifications and positions of the buttons and buttonholes should be accurate, and the tension should be appropriate during stretching. There should be no leakage during stretching. The front and rear crotch should be smooth and flat. The length distance of the pants loop should be accurate, symmetrical, and the tightness should be suitable for the front and back positions, with a height tolerance of 0.3cm. The bag opening should be smooth and free from uneven tightness

Function of testing report:

1. Project bidding: Issue authoritative third-party CMA/CNAS qualification report

2. Online e-commerce platform entry: Quality inspection report recognized by major e-commerce platforms

3. Used as a sales report: issuing legally effective testing reports to make consumers more confident

4. Papers and research: Provide professional personalized testing needs

5. Judicial services: providing scientific, fair, and accurate testing data

6. Industrial problem diagnosis: Verify the troubleshooting and correction of industrial production problems

100% inspection and testing process:

1. Telephone communication and confirmation of requirements

2. Recommend solutions and confirm quotations

3. Mail samples and arrange testing

4. Progress tracking and result feedback

5. Provide reports and after-sales service

6. If urgent or priority processing is required

Testing and testing characteristics:

1. The testing industry is fully covered, meeting different testing needs

2. Fully cover the laboratory and allocate localized testing nearby

3. Engineers provide one-on-one services to make testing more accurate

4. Free initial testing, with no testing fees charged

5. Self service order delivery for free on-site sampling

6. Short cycle, low cost, and attentive service

7. Possess authoritative qualifications such as CMA, CNAS, CAL, etc

8. The testing report is authoritative and effective, and is generally used in China